看了，真的的需要安装驱动
**
**
** VIA Rhine Family Fast Ethernet Adapter
**
** Linux Driver
**
** v5.08 Nov. 2006
**
**
Introduction:
=============
The instructions listed below are for linux driver installation. You must
compile the source code to generate rhinefet.o(rhinefet.ko in 2.6.x kernel,
please remember to replace rhinefet.o with rhinefet.ko in the following
sentences if you are using 2.6.x kernel) and use insmod command to insert
rhinefet.o as module.
Contents of the Subdirectory:
=============================
linux.txt This file.
Makefile Makefile for generating driver object file
rhine_maic.c The linux core driver source code file
rhine_proc.c The source to create proc entries
rhine_wol.c The WOL supporting source file
rhine.h The extended driver header file
rhine_proc.h The header file for proc entries
rhine_wol.h The WOL supporting header file
rhine_cfg.h The general and basic info header file
kcompat.h The header file for Linux kernel version
compatibility.
osdep.h OS depended function and macro defined
rhine_hw.h Rhine series MAC register supporting header file
rhine_hw.c shared function for accessing and configurating Rhine series MAC
Kernel Supported
================
This driver supports linux kernel version 2.2.x, 2.4.x and 2.6.x now.
For 2.6 kernel, it supported up to 2.6.18 in this version.
CPU Supported
=============
This driver supports x86 and AMD64 based linux system.
Installation
============
Please enter the following commands at the UNIX prompt. Remember, UNIX is
case sensitive.
1) Create a temporary directory:
mkdir /temp
2) Change to the temporary directory:
cd /temp
3) Copy driver (rhinefet.tgz) from DOS disk, (mcopy below is one tool in
mtools, if you didn't install mtools, you can type
'mount -t msdos /dev/fd0 /mnt' and use 'cp /mnt/rhinefet.tgz /temp'
command to copy the driver to the temporary directory):
mcopy a:rhinefet.tgz .
4) untar the archive file:
tar xzvf rhinefet.tgz
cd src
5) Compile the driver source files and it will generate rhinefet.o, and
copy it to correct driver installation path (The installation directory
is different in different kernel versions. In 2.4.x/2.6.x kernel, the path
is /lib/modules/KERNEL_VERSION/kernel/drivers/net/, and in 2.2.x kernel,
the path is /lib/modules/KERNEL_VERSION/net/, the KERNEL_VERSION (see
above) means the kernel version of your Linux distribution. If you don't
know your kernel version , please run 'uname -r' command in command
line. The kernel version will look like '2.2.16', '2.4.2-2smp' etc.) :
make install
6) Check configuration file (/etc/modules.conf or /etc/conf.modules or
/etc/modprobe.conf, it depends on your Linux distribution) for loading
kernel modules. Make sure the first line below is appeared in the
configuration file, where # is the interface number (eg: alias eth0
rhinefet). If you need to set the driver options, below second line is
an example to set the NIC to 100Mbps fullduplex mode (remember to unmark
the line if it is put in the configuration file).
alias eth# rhinefet
#options eth# speed_duplex=2
7) Reboot now:
shutdown -r now
8) Install your driver module (If the driver module is in the wrong place,
an error message will appear, and say that can't find the driver
module):
insmod rhinefet.o
9) Use ifconfig command to assign the IP address, where # is network
interface number:
ifconfig eth# <IP>
10) Check the interface works:
ping <remote_host_IP>作者: lfghx 时间: 2012-2-3 09:42
